Exfo ftb-200 user manual pdf

Dating > Exfo ftb-200 user manual pdf

Download links: → Exfo ftb-200 user manual pdf → Exfo ftb-200 user manual pdf

From the main window, tap the Test Tools button. Position the adapter so that you can see the retaining screw as shown below. Note: The cleaner makes a clicking sound to indicate that the cleaning is done.

Tap Windows Mobility Center. Otherwise, all your files will be lost. From the main window, tap the System Settings button. To remove Favorites: 1. Under Power Options, tap Change what the power buttons do. Tap Platform Imaging Utility to display the corresponding application.

If necessary, tap Change settings, and then, when the application prompts you to authorize the changes to your unit, select Yes. In the EXFO KernosHost Properties dialog box, tap the Security tab. Note: To have access to automation features on an FTB-2 unit, you must purchase the Automation option.

EXFO FTB-2 User Manual - Remove the battery compartment door.

Information provided by EXFO is believed to be accurate and reliable. However, no responsibility is assumed by EXFO for its use nor for any infringements of patents or other rights of third parties that may result from its use. The limits set by these standards are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Note: You will only be able to work with Wi-Fi and Bluetooth® if you have purchased the RF option. The full text of the EU declaration of conformity is available at the following Internet address: www. FTB-2 Pro: Windows 10 IoT Enterprise or Windows 8. Units running Windows 8. Green, blinking At least one battery is charging. Yellow, blinking The unit and its modules would be using more power than what is available from the batteries. Yellow The global level of batteries is low. Yellow, blinking The unit and its modules would be... The table below shows an overview of their purpose. Standard three-wire power cord connected to standard power outlet FTB-4 Pro—indoor use only. The table below gives... For more information on how to activate software options for your unit, see Activating Software Options on page 74. By doing so, you will... For a complete list of accessories available for your unit, refer to its technical specifications or contact EXFO. Make sure to read them carefully when they apply to your situation. The unit is equipped with a protective conductor terminal. The unit is equipped with a frame or chassis terminal. Refer to the user guide or the online help of the different modules for the exact information. The FTB-4 Pro model uses an international safety standard three-wire power cable. This cable serves as a ground when connected to an appropriate AC power outlet. It provides reinforced insulation between primary and secondary, and is suitably rated for the country where the unit is sold. In this case, always ensure that you comply with the most restrictive conditions either module or platform. Note: To ground your unit, you need a grounding wire 18 AWG minimum with a U-shaped terminal. Turn the grounding stud clockwise to screw it tight. Ground the other end of the wire as per your local regulation. Your unit is now grounded properly. With the FTB-2 and FTB-2 Pro models, you can also hold your unit with the provided hand strap. Note: If you wish to use a shoulder strap sold separately by EXFO , you must first install the carry handle. To install the carry handle: 1. Slide each end of the handle under the corresponding metal rod. Pull on the straps until the base of each D-shaped metal ring rests on the corresponding rod. Slide the straps through the D-shaped rings. Fold the large part of the handle over the straps, and secure it in place with the Velcro. You are now ready to use the carry handle, or to attach a shoulder strap see Installing the Shoulder Strap on page 39. To install the FTB modules adapters: 1. Position the adapter so that you can see the retaining screw as shown below. Slide the adapter into the unit until it stops, making sure that the retaining screw is well aligned with the corresponding screw hole on the unit. Using a screwdriver, turn the retaining screw clockwise to secure the adapter in place. Turn retaining screw clockwise 4. If necessary, repeat the steps above with another adapter. You are now ready to work with FTB modules. Using a screwdriver, turn the retaining screw counterclockwise until it is loose. Since it is a captive screw, you cannot remove it completely. Place your fingers just under the protruding edge on the faceplate of the adapter, and then slide the adapter out of the unit. If necessary, repeat the steps above with the second adapter. You are now ready to work with FTBx modules. This will result in immediate and irreparable damage to both the module and unit. To avoid damaging your unit, use it only with modules approved by EXFO. MPORTANT You can insert FTBx modules, FTB modules, or a combination of both in your unit. Push the module all the way to the back of the slot, until it stops. If you are working with an FTBx module, turn the two retaining screws clockwise until they are tightened. While applying slight pressure to the module, lift the mobile part of the retaining screw and use it to turn the retaining screw clockwise until it is tightened. Position the unit so that its right panel is facing you. If you are working with an FTBx module, turn the two retaining screws counterclockwise until they are loose. Since they are captive screws, you cannot remove them completely. Turn one locking screw counterclockwise until you can remove it completely. Turn locking screw counterclockwise 4b. Remove the three remaining screws in the same way. Position the unit so that the left panel is facing you. Hold the module by its sides or by the handles NOT by the connectors and pull it out. Note: On the FTBx modules, the retaining screws can be used as handles to pull out the module safely. Cover empty slots with the supplied protective covers. AUTION Failure to reinstall protective covers over empty slots will result in ventilation problems. Note: Should the unit ever stop responding, you can force a hardware reset by pressing and holding down the power button for more than 15 seconds. From the right side of the screen, swipe left to display the Charm bar. For more information, see the section about working with Windows 8. From the main window, tap the System Settings button. Tap Hardware and Sound. Under Power Options, tap Change what the power buttons do. Tap Changes settings that are currently unavailable. Tap Save changes to confirm the changes and return to the Power Options window. Tap OK to confirm the changes and return to the System Settings window. Once the configuration is complete in Windows, an EXFO wizard will be displayed, allowing you to read the user documentation for important safety information, and to read and accept the EULA related to your unit and instruments. When the EXFO wizard is displayed, follow the on-screen instructions. Tap Finish to close the wizard and start working. Note: If ToolBox X has been sent to the notification area, from this location, right-click the icon, and then select Restore ToolBox X. If necessary, tap the Modules button to display the modules window. Inserted module Applications specific to the module 2. On the row corresponding to the desired module, tap the icon of the application with which you want to work. From the unit's front panel, press the button. From the taskbar, tap the on-screen keyboard icon located to the left of the clock. Enter the data as required. Close the keyboard when you are done entering data. From the right edge of the screen, swipe towards the left. If you want to hide the shortcut menu without performing any action, simply tap anywhere outside the menu. The update files must be copied to the location that has been specified for the deployment packages in Update Manager. If you do not intend to download files directly on your unit, connect a USB memory key to one of the USB ports of the computer and copy the installation files to this USB key. If you do not intend to download files directly on your unit, connect a USB memory key to one of the USB ports of the computer and copy the installation files to this USB key. From the main window, tap the System Settings button, and then tap Options Activation. Tap OK to close the confirmation message, and then Close to exit. Note: At this point, if you have used a USB key to copy your key file, you can remove it as it is not required to use your new options. In all cases, EXFO does not provide any support for the installation, use or troubleshooting of third-party software. Should you need help, refer to the corresponding third-party software documentation or technical support. To secure your unit: Connect your lock to the security slot located on the left panel of your unit. Printer To print documents such as reports directly from you unit. If you prefer to use a network printer, you can also configure one. For more information, see Configuring Network Printers on page 104. The software will automatically detect its presence. Your device is automatically recognized and immediately usable provided that it uses the drivers already available on your unit. To adjust the display brightness: 1. From the main window, tap the System Settings button. Tap Windows Mobility Center. Move the Brightness slider until the screen appearance is to your liking. The new brightness value is taken into account immediately. Ensure that your headset is connected to the audio port located on the top panel of the unit. From the main window, tap the System Settings button. Tap Hardware and Sound. Under Sound, tap Manage audio devices. Select the Recording tab. Ensure that your microphone is selected, and then tap Properties. Tap OK to confirm your new settings and close the window. Tap OK to close the window and return to Control Panel. From the main window, tap the System Settings button. Tap Windows Mobility Center. Move the Volume slider until the sound level is to your liking. Note: You can also access the sound level slider by tapping the icon from the taskbar. The new value is taken into account immediately. This will ensure a greater accuracy of the touchscreen, especially along the edges and in corners. From the main window, tap the System Settings button. Tap Touch Screen Calibration. Tap the button corresponding to the type of calibration or linearization that you want to perform. When you see the message indicating that the calibration is complete, tap OK to return to the System Settings window. From the main window, tap the System Settings button. Tap Hardware and Sound. Tap Pen and Touch. If you want to use the right-click feature with your unit, select the Enable press and hold for right-clicking check box. Clear the check box if you prefer not to use this feature. If you want to modify the response time of the right-click, move the Speed or Duration sliders to adjust the configuration to your needs. Tap OK to confirm your changes. From the main window, tap the System Settings button. From the User Accounts window, clear the Users must enter a user name and password to use this computer check box. Tap OK to confirm. To disable the automatic logon: 1. From the main window, tap the System Settings button. From the User Accounts window, select the Users must enter a user name and password to use this computer check box. Tap OK to confirm and to return the System Settings window. At next startup, you will have to specify the user name and password. From the main window, tap the System Settings button. Tap OK to use the new settings. Tap Cancel to exit without using the new settings. Note: The new settings will be taken into account the next time ToolBox X is started. To configure the printer: 1. From the main window, tap the System Settings button. Under Hardware and Sound, tap View devices and printers. Tap Add a printer. Follow the on-screen instructions. Once the keyboards are added, you can switch easily from one input language to another. Values are kept in memory even when you turn the unit off. From the main window, tap the System Settings button. Under Clock, Language, and Region, tap Add a language. Select the desired language from the list. If you want to select another keyboard layout than the one that has been added by default, proceed as follows. Under Input method, tap Add an input method. Select the desired keyboard layout, and then tap Add. They remain in the language configured at time of purchase. However, the EXFO applications are displayed in the selected language when available. From the list of languages, select the desired one. You are now ready to start entering text in the selected input language. Note: Modifying the input language does not modify the language of the interface. Ensure that your unit has access to the Internet. From the main window, tap the System Settings button. Under Clock, Language, and Region, tap Add a language. Tap Add a language. Browse the list of languages, and then select the one that you want to use. Tap Open to access the list of sub-languages. Select the desired sub-language, and then tap Add. Select the desired language from the list. Tap Download and install language pack. When the application prompts you to allow the installation, tap Yes. The installation may take a few minutes. When the installation is complete, restart your unit. To set date and time formats: 1. From the main window, tap the System Settings button. Under Clock, Language, and Region, tap Change date, time, or number formats. Refine the settings according to your needs. Tap Apply to confirm, and then OK to close the window. The new values are taken into account immediately. To adjust the date, time or time zone: 1. From the main window, tap the System Settings button. Tap Clock, Language, and Region. Under Date and Time, tap Set the time and date. Modify the settings according to your needs, and then tap OK. Tap Apply to confirm, and then OK to close the window. The new values are taken into account immediately. You can delete custom power plans that you no longer use, but not the predefined plans. From the main window, tap the System Settings button. If necessary, tap Change settings that are currently unavailable. From the list of available power plans, select the desired set of parameters. The new values are taken into account immediately. From the main window, tap the System Settings button. From the list on the left, tap Create a power plan. Select a power plan that will serve as a basis. Enter a name, and then tap Next. Modify the parameters to suit your needs. From the main window, tap the System Settings button. If the custom power plan that you want to delete is currently in use, you must select another plan first. Tap Change plan settings appearing next to the power plan. If you want to modify the parameters, proceed as follows: 6a. If necessary, tap Change settings that are currently unavailable. Modify the parameters to your needs. If you want to delete the power plan, tap Delete this plan, and then confirm the deletion. The changes are taken into account immediately. To set the ToolBox X behavior: 1. From the main window, tap the System Settings button. Tap ToolBox X Setup. For more information on the different ways to turn off your unit, see Turning Off Your Unit on page 57. Tap OK to confirm your settings and close the window. To configure the Internet options: 1. From the main window, tap the System Settings button. Tap Network and Internet. Go to the Connections tab. Modify the settings using the information provided by your network administrator. Tap OK to return to the Control Panel window. Contact your mobile service provider for more information. If it is not done already, install EXFO Link: 3a. Ensure you have access to an Internet connection. Ensure that you have a Google account to be able to download EXFO Link. If it is not done already, enable the geolocation feature: 5a. From the main window, tap Note: Depending on the smart device you are using, the application settings could be found in the menu button instead. Under GENERAL SETTINGS, select the Geolocation option. Note: For more information on how to modify other settings related to geolocation, refer to the EXFO Link user documentation. Tap to return to the main window. On your smart device, ensure that EXFO Link is running, configured properly, and that the mobile hotspot that you have created is available. To configure the parameters via Windows Mobility Center: 1. From the main window, tap the System Settings button. Tap Windows Mobility Center. Set the parameters as desired. Setting Other Parameters You can also configure many other parameters via the Control Panel window. Refer to Microsoft Windows documentation for details. Select the desired printer PDF creation tool by default. Tap Print to start the printing process, and follow the on-screen instructions. From the main window, tap the Utilities button. Browse through the folders to find the desired PDF file. The file opens automatically in the PDF viewer. Note: If a keyboard is connected to your unit, you can also press the Windows logo key + PRINT SCREEN. Enter the desired Web address in the address bar and tap the button located at the right of the address bar to start browsing. Close the window to return to the Utilities window. Most of the time, this application is installed automatically the very first time you connect a USB modem key to your unit. In all cases, you only need to install this application once. When you have finished working, disconnect from the mobile network, and then remove the USB modem key from your unit. If necessary, turn on your unit and wait for the startup sequence to complete. On your smart device, ensure that EXFO Link is running and that the mobile hotspot that you have created is available. Connect your unit to the mobile hotspot as you would do with any other wireless network. From the main window, tap the Utilities button, then tap GPS Coordinates Viewer. The GPS coordinates are displayed. When your work is finished, tap to close the utility. To add Favorites: 1. From the main window, tap the Favorites button. Repeat the previous steps with all the Favorites that you want to add. Tap OK to apply the changes and close the window. To remove Favorites: 1. From the main window, tap the Favorites button. Removing a Favorite from the list does not uninstall the application from the unit. Tap OK to apply the changes and close the window. From the main window, tap the Favorites button. Tap the icon corresponding to the application that you want to use. From the main window, tap the Favorites button. Select a location and type a name for the Favorites list. Tap OK to apply the changes and close the window. From the main window, tap the Favorites button. Select the desired Favorites list. Tap OK to apply the changes and close the window. From the main window, tap the Utilities button. Using the Text Editor You can use Microsoft Notepad directly from your unit. To use the text editor: 1. From the main window, tap the Utilities button. To access the applications: 1. From the main window, tap the Test Tools button. Tap the icon corresponding to the application that you want to start. Note: You can access the online help of the power meter and the VFL by tapping button from the power meter application. Connect the probe to one of the USB ports of your unit right or top panel. From ToolBox X, tap the ConnectorMax2 button to open the application. Note: You can access the online help by tapping the button from the ConnectorMax2 application. The file explorer is displayed. Folders Free disk space Note: The free disk space is also visible from the Platform tab tap in the lower right corner of the main window. Configure your unit as follows: ® 1a. From the notification area, tap the Bluetooth icon. From the Options tab, under Discovery, select the Allow Bluetooth devices to find this PC check box. Configure the computer as follows: ® 2a. From the notification area, click the Bluetooth icon. Ensure that the option allowing Bluetooth devices to find the computer is selected. Click OK to confirm. From the notification area, tap the Bluetooth icon. Tap Add a Bluetooth Device. From the list of Bluetooth devices, tap the item corresponding to the computer to which you want to transfer files. On the FTB-2 running Windows 10, FTB-2 Pro, or FTB-4 Pro, tap Pair. On the FTB-2 running Windows Embedded 8 Standard, the application tries to establish the pairing automatically. Note: If the computer or device that you want to select is already paired, you must remove the pairing first with the Remove device button. Transfer the files as follows. From the main window, tap the Utilities button. Tap Bluetooth File Transfer. Select the desired computer, and then tap Next. Tap the Browse button to select the file that you want to transfer, and then tap Next. Tap Finish when the transfer is complete. Note: To save power when your unit is running on batteries, you may wish to disable the Wi-Fi device when you do not use it. In Windows 10, tap Network. When you have finished, from the Networks list, tap Disconnect to stop communication with the wireless network. The communication between your unit and the device is established using the PuTTY application. The adapter will be detected automatically on your unit. From your unit, retrieve the COM port of the adapter as follows: 3a. From the main window, tap the System Settings button. Tap Hardware and Sound. Close the Device Manager. The unit is now ready to receive or send data. From the device, establish communication with the unit using your favorite communication tool PuTTY, HyperTerminal, etc. If you do not see the Windows. From the main window, tap the System Settings button. Tap System and Security. Tap Administrative Tools, and then double-tap Disk Cleanup. If you want to free up even more disk space by removing system files such as the files from the Windows. When the application prompts you to confirm the deletion of the folder, tap Delete Files. ® You can enable the Wi-Fi and Bluetooth communication as well as the mobile broadband USB modem key again at any time. From the right side of the screen, swipe left to display the Charm bar. Tap Settings, and then Change PC Settings. You must either use one of the VPN clients available directly in Windows or provide the installation files for another VPN client yourself. To add a VPN connection: 1. From the main window, tap the System Settings button. Tap Network and Internet. Under Network and Sharing Center, tap View network status and tasks. Tap Set up a new connection or network. Tap Connect to a workplace, and then tap Next. Follow the on-screen instructions. To connect to a VPN from your unit: 1. From the main window, tap the System Settings button. Tap Network and Internet. Under Network and Sharing Center, tap Connect to a network. Enter your sign-in information to the VPN, and then tap OK. If you are not sure about the information that you should provide, contact your network administrator. Usually, this user name must correspond to the user name of the person currently logged on the unit. Otherwise, you will disconnect the person that was already connected. From the main window, tap the System Settings button. Under Remote Desktop, select Allow remote connections to this computer. Tap OK to confirm the changes and return to the System Settings window. Turn on both the computer and the unit. On your unit, from Toolbox X, tap the button located at the bottom of the button bar. When the application prompts you, enter your user name and password. Click OK to open the session. To allow a user with limited accounts to use Remote Desktop: 1. From the main window, tap the System Settings button. Under Remote Desktop, select Allow remote connections to this computer. From the Remote Desktop Users dialog box, tap Add. From the Select Users dialog box, tap Advanced. Tap Find Now to let the system find and display the list of users. Repeat steps 7 to 9 with all the users to which you want to grant access rights. From the Remote Desktop Users dialog box, tap OK. From the System Properties dialog box, tap OK to confirm the changes and return to the System Settings window. However, all users having administrator user rights will be able to modify this setting at any time. To prevent users from connecting to the unit using Remote Desktop: 1. From the main window, tap the System Settings button. Tap OK to confirm the changes and return to the System Settings window. Know the password same for all users by default. From the main window, tap the System Settings button. From the notification area, right-click the UltraVNC icon. From the shortcut menu, tap Admin Properties. Note: The VNC and view-only passwords are independent of each other. They do not have to be identical. Tap Apply, and then OK. MPORTANT EXFO does not provide licenses for UltraVNC Viewer. Always ensure that you are entitled to install it on your computer. To install the UltraVNC Viewer on your computer: 1. Turn on both the computer and the unit. On your unit, ensure that ToolBox X is open. Scroll down until you can see the IP address. Write down the IP address, and then close the window. Note: It may take a few seconds before you see the IP address on the list. From your computer, start the UltraVNC Viewer. When the application prompts you for a password, enter it and click OK to confirm. To add exceptions to the firewall: 1. From the main window, tap the System Settings button. Tap System and Security. Under Windows Firewall, tap Allow an app through Windows Firewall. Tap the Change settings button. Tap the Allow another app button. Select the desired application from the list, and then tap Add. Ensure that the Private and Public settings of the added application suit your needs. When you have finished, tap OK to confirm the changes and return to the Control Panel window. You can later import the generated text file tab-delimited directly into Microsoft Excel. From the main window, tap Test Tools. From IP Testing Tools, select the Ping tab. Tap the Start button. You can stop a ping test at any time by tapping the Stop button. You can later import the generated text file tab-delimited directly into Microsoft Excel. Tap the Start button. You can stop a trace route test at any time by tapping the Stop button. If necessary, modify the suggested file name. Note: To have access to automation features on an FTB-2 unit, you must purchase the Automation option. EXFO supplies commands that follow the guidelines determined by the SCPI consortium for many instruments. Note: You must make the choice of output unit for each instrument offering such a feature. Refer to the user guide of each optical instrument for a list of available commands and queries. Tap the System Settings button, then tap Instrument Control Configuration. Tap Change settings, and then, when the application prompts you to authorize the changes to your unit, tap Yes. If you cleared the check box because you prefer to block automation, you can go directly to step 6. Note: If the selected communication type does not match the protocol that will actually be used, an error message is displayed when attempting to control the instruments. Tap Apply to confirm your changes. Tap the Default settings button. Tap Apply to confirm your changes. Right-click My Computer, and then select Properties. In the My Computer Properties dialog box, tap the COM Security tab. Under Access Permissions, tap Edit Limits. In the Access Permission dialog box, ensure that the Distributed COM Users group appears in the Group or user names list. In the My Computer Properties dialog box, tap the COM Security tab. Under Launch and Activation Permissions, tap Edit Limits. Note: If you add a user explicitly, ensure to give remote access rights to the new user. In the My Computer Properties dialog box, tap the COM Security tab. Under Access Permission, tap Edit Limits. In the Access Permission dialog box, tap Add. In the Select Users or Groups dialog box, under Enter the object names to select, type the name of the user to whom you want to give access rights. Under Permissions for new user , ensure Allow is selected for Remote Access. In the My Computer Properties dialog box, tap the COM Security tab. Under Launch and Activation Permissions, tap Edit Limits. In the Select Users or Groups dialog box, under Enter the object names to select, type the name of the user to whom you want to give start and activation access rights. In the Launch Permission dialog box, select the name of the new user. Under Permissions for new user , ensure Allow is selected for both Remote Launch and Remote Activation. If you do not specify local access rights, no user will be able to access EXFO KernosHost and, therefore, no user will be able to start ToolBox X. To customize the specific security parameters: 1. Tap the General tab. In the Authentication Level list, select Default. In the EXFO KernosHost Properties dialog box, tap the Security tab. Under Launch and Activation Permissions, select Customize, and then click Edit to edit the list of allowed users. In the Select Users or Groups dialog box, under Enter the object names to select, type the name of the user to whom you want to give start and activation permissions for remote access. In the Launch and Activation Permission dialog box, select a user. To allow this user to start and activate the unit remotely, select Allow for all four permission choices. Repeat steps 10 and 11 for each newly added user. In the EXFO KernosHost Properties dialog box, tap the Security tab. Under Access Permissions, select Customize, and tap Edit to edit the list of allowed users. In the Access Permission dialog box, tap Add. Repeat steps 19 and 20 for each newly added user. Tap OK to close the Access Permission dialog box. Tap OK to close the EXFO KernosHost Properties dialog box. The EXFO IcSCPIAccess Class component, located on your unit, can now be accessed with DCOM. EXE, you need Administrator access rights. If you want to subscribe to EXFO IcSCPIAccess Class component events, you need to set security parameters on the client computer. To enable DCOM on the client computer: 1. Select Enable Distributed COM on this computer. Under Default Distributed COM Communication Properties, in the Default Authentication Level list, select Connect. In the Default Impersonation Level list, select Identify. If ANONYMOUS LOGON is not listed under Group or user names, tap Add to add it. For more information on enabling events with DCOM, refer to AppId Key in MSDN Documentation. From DCOM Config, right-click EXFO KernosHost, and select Properties. In the EXFO KernosHost Properties dialog box, tap the Security tab. Under Launch and Activation Permissions and Access Permissions, select Use Default. This ensures the EXFO IcSCPIAccess Class component uses the default lists instead of the customized lists. MPORTANT Before being able to control instruments with SCPI commands, or control them remotely using a dedicated application such as EXFO Remote ToolBox, you must first allow remote access to these instruments. Regardless of how you intend to control your instruments, you can configure the following parameters for each of them: Enable or disable remote access. Note: Some instruments do not support remote control. From the main window, tap the System Settings button. Tap Remote Control Configuration. If necessary, tap Change settings, and then, when the application prompts you to authorize the changes to your unit, select Yes. If desired, under Description, type a description that will help you identify the instrument. Note: You can enter up to 10 characters. The description can correspond to the test interface ID or to any other short text of your choice. Refer to the corresponding instrument documentation for more details. From the main window, tap the System Settings button. Tap Remote Control Configuration. If necessary, tap Change settings, and then, when the application prompts you to authorize the changes to your unit, select Yes. The LINS of the instruments that were already in the system when you selected the LINS offset value will not be updated. Note: To have access to automation features on an FTB-2 unit, you must purchase the Automation option. Bits Mnemonics Bit Value Power On PON User Request URQ Command Error CME Execution Error EXE Device-Dependent Error DDE Query Error QYE Not Used N. Error Available EAV Not Used N. The controller will then find which device generated a SRQ its RQS bit is set and the causes of it. Element used in the construction of various numeric data types. Can take any value between 0 and 9 inclusively corresponds to ASCII character codes 48 to 57, in decimal. Do not include braces in your program message. Mandatory to separate keywords. Can be omitted at the beginning of a program message. For example, you can use either :SYST:ERR or SYST:ERR. For a complete list of possible errors, see the appendix on SCPI-based errors. To monitor remote commands: 1. From the main window, tap the Test Tools button. Depending on which type of communication protocol you are using, select IC Monitor or SCPI Telnet Monitor. To exit the monitoring utility, tap For more information, see the section on using your unit in an automated test environment. To exit the monitoring utility, tap Exit. While applying light pressure to avoid breaking the detector window , gently rotate the cleaning tip on the detector window. Repeat step 4 with a dry cleaning tip or blow dry with compressed air. Discard the cleaning tips after one use. Insert the cleaning tip into the optical adapter, and push the outer shell into the cleaner. Note: The cleaner makes a clicking sound to indicate that the cleaning is done. When not using your unit, EXFO recommends using the screen protector that came with it. Otherwise, the operating time might be reduced. This will ensure that you get the optimum performance out of the batteries. From the main window, tap the System Settings button. From the list of available power plans, locate the set of parameters that you want to modify. Tap Change plan settings appearing next to the power plan. If necessary, tap Change settings that are currently unavailable. Tap Change advanced power settings. Under On battery, enter the new value. Under On battery, enter the new value. The changes are taken into account immediately. You can easily replace the batteries while the unit is running, as long as the unit remains powered by another reliable power source during the operation. For this reason, you can only replace them with batteries of the same type and model. ARNING RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. Lift the mobile part of the battery compartment screws and turn the screws counterclockwise until the compartment door is loose. Since they are captive screws, you cannot remove them completely. Turn screws counterclockwise Battery compartment 1d. Remove the battery compartment door. The battery must be inserted in the first battery slot as indicated on the label affixed to your unit. Slide in the new battery, and push it toward the back until it stops. Repeat steps 2 and 3 with the other battery if it also needs replacement FTB-2 Pro and FTB-4 Pro only. Position the battery compartment door so that you can see its two screws. Lift the mobile part of the compartment screws and, while applying slight pressure, turn the screws clockwise until they are tightened. These could cause a short-circuit leading to a fire or an explosion. Turn off your unit. Disconnect the unit from its external power source and remove the batteries. Put on a wrist or an ankle antistatic strap and ensure that the end of its wire is grounded properly. Remove the protective cover. MPORTANT Do not discard the protective cover. You will need it to protect the power meter bay if you ever send the power meter for recalibration. In this case, repeat the installation procedure. If the problem persists, contact EXFO. MPORTANT Do not discard the screws. You will need them to secure the protective cover, and the power meter in its bay when it is back from calibration. Using a screwdriver, secure the protective cover in place with the screws that you have removed at step 5. Remove your antistatic strap. Connect your unit to an external power source if desired. If you want to update EXFO applications, see Installing or Upgrading the Applications on page 71. The third-party applications will need to be updated manually. Under Update status, tap Check for updates. Follow the on-screen instructions. Your unit will need an Internet access for the updates. To manage the updates for Windows applications: 1. From the main window, tap the System Settings button. Tap System and Security. Under Windows Update, tap Turn automatic updating on or off. Select the update options that best suit your needs. Tap OK to confirm your changes and return to Control Panel. Turn off the unit and unplug the power cord. Using a flat-head screwdriver as a lever, pull the fuse holder out of the unit. Make sure the fuses are placed firmly in the holder prior to reinsertion. Firmly push the fuse holder into place. Problem Possible Cause Solution My unit does not start. It is not connected to a Make sure that the external power source. The SIM card has not been Contact your provider of activated or there is a mobile services. There is a problem with the mobile network. If EXFO Viewer utility. Link is not installed on the smart device, see Getting Ready to Retrieve Geolocation Information on page 137. AC adapter is connected to... This folder now uses too much disk space. Follow the on-screen instructions. In Windows Embedded 8 Contact EXFO if you think that Standard, when you select a the language that was language that you have configured at time of purchase installed manually, the does not cover your needs. MPORTANT The WIM files that you create are based on the serial number of your unit. This means that the WIM files created on one unit are only valid to restore this particular unit. Doing so may severely damage your unit. Damaged units will need to be sent back to EXFO for repair. The recovery operations that are offered for your unit depend on the operating system that it is running. To create a WIM file for your unit: 1. From the task bar, tap the Start button , and then Settings 2. Under Advanced Startup, tap Restart now. Under Choose an option, tap Troubleshoot. Tap Platform Imaging Utility to display the corresponding application. Connect a USB key to your unit. From the Platform Servicing and Imaging Utility wizard, select Create a WIM file, an then tap Next. Note: The time required to create the image varies with the configuration of your unit. When the operation is complete and the application prompts you, tap 15. Disconnect the USB key. Tap Cancel to return to the Welcome window of the utility. The WIM file is ready for future use. If desired, back up your data. From the task bar, tap the Start button , and then Settings 4. Under Advanced Startup, tap Restart now. Under Choose an option, tap Troubleshoot. Tap Platform Imaging Utility to display the corresponding application. Connect the USB key with the desired WIM file to your unit. From the Platform Servicing and Imaging Utility wizard, select Restore unit from a WIM file, and then tap Next. Read the warning, and then tap Start to restore the unit with the selected image. When the operation is complete and the application prompts you, disconnect the USB key, and then tap OK. The unit will restart. If desired, back up your data. From the task bar, tap the Start button , and then Settings 4. Under Advanced Startup, tap Restart now. Under Choose an option, tap Troubleshoot. Tap Platform Imaging Utility to display the corresponding application. The unit will restart. Configure the regional parameters, and accept the license agreements as you did when you first received your unit see Configuring Your Unit At First Startup on page 63. Otherwise, all your files will be lost. To create a WIM file for your unit: 1. On your unit, from the right side of the screen, swipe left to display the Charm bar. On an FTB-2 Pro, tap Update and recovery. On an FTB-2 Pro, tap Recovery. On an FTB-2, tap General, and then scroll down the list. Under Advanced Startup, tap Restart now. Under Choose an option, tap Troubleshoot. Tap Platform Imaging Utility to display the corresponding application. Connect a USB key to your unit. From the Platform Servicing and Imaging Utility wizard, select Create a WIM file, an then tap Next. Locate the USB key, and then double-tap its identifier to access the contents. Select the desired folder. Enter a file name, and then tap Save. Note: The time required to create the image varies with the configuration of your unit. When the operation is complete and the application prompts you, tap 16. Disconnect the USB key. If desired, back up your data. On your unit, from the right side of the screen, swipe left to display the Charm bar. On an FTB-2 Pro, tap Update and recovery. On an FTB-2 Pro, tap Recovery. On an FTB-2, tap General, and then scroll down the list. If you want to refresh or reset your unit, proceed as follows: 7a. Tap the Get started button corresponding to your choice. To refresh your unit To reset your unit 7b. Follow the on-screen instructions. If you want to restore your unit with a WIM file , proceed as follows: 8a. Under Advanced Startup, tap Restart now. Under Choose an option, tap Troubleshoot. Tap Platform Imaging Utility to display the corresponding application. Connect the USB key with the desired WIM file to your unit. From the Platform Servicing and Imaging Utility wizard, select Restore unit from a WIM file, and then tap Next. Read the warning, and then tap Start to restore the unit with the selected image. When the operation is complete and the application prompts you, disconnect the USB key, and then tap OK. The unit will restart. Note: The user guides of all products are available from the Library section of the EXFO Web site www. To view the online help: From ToolBox X or an instrument application, tap or the equivalent. The Technical Support Group is available to take your calls from Monday to Friday, 8:00 a. You can also find the contact information if you ever need to reach EXFO. Retrieving the Serial Number of Your Unit The serial number of your unit is easily accessible from ToolBox X. In the lower right corner of the main window, tap 2. Tap the About tab. The version number is displayed. In the lower right corner of the main window, tap 2. Tap the Platform tab. The version numbers are displayed. In the lower right corner of the main window, tap 2. Tap the Platform tab. The information is displayed one section per network interface. From the main window, tap the System Settings button. Under Network and Internet, tap View network status and tasks. Tap the link corresponding to the Wi-Fi network. From the Wi-Fi Status window, tap Details. When your work is done, close the window. Close all other windows to return to ToolBox X. To retrieve the contact information: 1. In the lower right corner of the main window, tap 2. Tap the About tab. EXFO warrants this equipment against defects in material and workmanship for a period of one year from the date of original shipment. EXFO also warrants that this equipment will meet applicable specifications under normal use. Return the equipment, prepaid, to the address given to you by support personnel. Be sure to write the RMA number on the shipping slip. EXFO will refuse and return any package that does not bear an RMA number. The information is supplied for guidance only. For more detailed information, please refer to IEEE 488. The second diagram below illustrates the syntax. The third diagram illustrates the syntax. The length will then be 13 bytes. The actual response will begin at byte number 5, in this case. The returned information is sent in the long form and in upper case. The length will then be 13 bytes. The actual response will begin at byte number 5, in this case. For information on these values, see Applicable Data Types for Output —IEEE 488. The , expressed in base 2, represents the bit values of the Standard Event Status Enable Register. See the contents of this register below. Standard Ev ent Status Enable Register N. Reading the Standard Event Status Register clears it. See the contents of this register below. Standard Event Status Register N. The response is organized into four fields separated by commas. The field definitions are as follows: Field 1 Manufacturer : EXFO Inc. However, using a service request eliminates the need to poll the Standard Event Status Register thereby freeing the controller to do other useful work. The receipt of an response indicates that all pending selected device operations have been completed. The value ranges from 0 through 255. The , expressed in base 2 binary , represents the bit values of the Service Request Enable Register. When converted to binary base 2 , the represents the current bit values of the Service Request Enable Register. See the content of this register below. These commands are fully explained on the following pages. SYSTem DATE ,, DATE? The allowed elements for this parameter are: ASCii PACKed. When the PACKed data format is selected, the optional parameter it not used. The list of contains the names of all logical instruments and groups. The is rounded to the nearest integer. Its range is 1 to 12 inclusive. The number 1 corresponds to January, 2 to February, and so on. Example s SYST:DATE 2014,07,29 See Also SYSTem:DATE? Description The SYSTem:DATE query returns the instrument's internal calendar. The is always rounded to the nearest integer. It ranges from 0 to 59 inclusively. When this element is rounded to 60 it shall be set to 0 and the minute value incremented. Any other carries shall be rippled through the date. Example s SYST:TIME 12,47,29 See Also SYSTem:TIME? The ranges from 0 to 59. The resolution of the clock is the second. Revision, where Year represents the year-version that is 1990 and Revision represents an approved revision number for that year. If no approved revisions are claimed, then this extension is 0. For example when loading memory tables or when sending a SYSTem:SET parameter from an unknown instrument. The definition of what constitutes missing media is device-specific. The definition of what constitutes protected media is device-specific. This code is device-dependent. For information on how to configure your unit for DCOM control, see Configuring DCOM Access to Your Unit on page 243. For information on timeout setting, see Initialize on page 465. Details on how to correctly set the format can be found below. QueryUnterminated: This error will occur if the output queue is empty for example, no query has been made previously. Initialize Timeout Parameter s Timeout: Required. A numeric value corresponding to the delay in milliseconds. Notes If the Initialize method is not invoked, the default value is 10 000 milliseconds. Notes This property can be used in conjunction with RequestService event see RequestService on page 468 to find out why the device caused a Service Request SRQ. Note: The Telnet client is available on the FTB-500, FTB-2 running Windows 10, FTB-2 Pro, FTB-4 Pro, LTB-8, and IQS-600 controller if you intend to use these units as computers to connect to a Telnet server. Once it is done, perform step 3 again. Press ENTER to establish a connection with the Service. Note: If the connection cannot be established, the Connection to host lost message is displayed instead. Click to close the session. Click to close the session. Error At this moment, SESSION 2 knows that LINS10 is already in use by another session. Note: Both sessions must use these commands to ensure that they receive accurate information. For more information, see KILL LINS on page 485. The SCPI commands enclosed in BEGIN and END blocks will be executed in batch. Only the information of the remaining connected client is displayed. Syntax STATUS CONNECTION Examples Notes By default, any connection that is idle for 5 minutes or more is identified as Idle. Syntax STATUS MODULE Examples WHO M I? Description This command retrieves the IP address and the communication port of the current session. Syntax WHO M I?